spec no: dsan2822 rev no: v.3a date: feb/13/2017 page: 1 of 5 approved: wynec checked: allen liu drawn: l.t.zhang e rp: 1203014041 3.0x2.0mm right angle smd led part number: apda3020seck/j3-pf hyper red features z 3.0mmx2.0mm smd led,2.8mm thickness. z low power consumption. z ideal for back light and indicator z package : 2000pcs / reel. z moisture sensitivity level : level 3. z tinned pads for improved solderability. z rohs compliant. descriptions z the hyper red device is bas ed on light emitting diode chip made from algainp. z electrostatic discharge and power surge coul d damage the leds. z it is recommended to use a wrist band or anti- electrostatic gl ove when handling the leds. z all devices, equipment and machinery must be electri cally grounded. package dimensions notes: 1. all dimensions are in millimeters (inches). 2. tolerance is 0.2(0.008") unless otherwise noted. 3. the specifications, characteristics and technical data descri bed in the datasheet are subject to change without prior notice . 4. the device has a single mounting surface. the devi ce must be mounted according to the specifications. attention observe precautions for handling electrostatic discharge sensitive devices
spec no: dsan2822 rev no: v.3a date: feb/13/2017 page: 2 of 5 approved: wynec checked: allen liu drawn: l.t.zhang e rp: 1203014041 selection guide notes: 1. 1/2 is the angle from optical centerline where the lumi nous intensity is 1/2 of the optical peak value. 2. luminous intensity / luminous flux: +/-15%. * luminous intensity value is traceable to cie127-2007 standards. absolute maximum ratings at ta=25c electrical / optical characteristics at ta=25c notes: 1. wavelength: +/-1nm. 2. forward voltage: +/-0.1v. 3. wavelength value is traceable to cie127-2007 standards. 4. excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradat ion or premature failure. part no. emitting color (material) lens type iv (mcd) [2] @ 20ma v iewing angle [1] min. typ. 2 1/2 hyper red (algainp) water clear 7000 11000 10 *2300 *3800 apda3020seck/j3-pf symbol parameter emitting color typ. max. units test conditions peak peak wavelength hyper red 640 nm i f =20ma d [1] dominant wavelength hyper red 625 nm i f =20ma ? 1/2 spectral line half-width hyper red 20 nm i f =20ma c capacitance hyper red 27 pf v f =0v;f=1mhz v f [2] forward voltage hyper red 2.2 2.8 v i f =20ma i r reverse current hyper red 10 ua v r =5v parameter values units power dissipation 84 mw dc forward current 30 ma peak forward current [1] 150 ma reverse voltage 5 v operating temperature -40c to +85c storage temperature -40c to +85c notes: 1. 1/10 duty cycle, 0.1ms pulse width. 2. relative humidity levels maintained between 40% and 60% in pr oduction area are recommended to avoid the build-up of static e lectricity ? ref jedec/jesd625-a and jedec/j-std-033.
spec no: dsan2822 rev no: v.3a date: feb/13/2017 page: 3 of 5 approved: wynec checked: allen liu drawn: l.t.zhang e rp: 1203014041 hyper red apda3020seck/j3-pf
spec no: dsan2822 rev no: v.3a date: feb/13/2017 page: 4 of 5 approved: wynec checked: allen liu drawn: l.t.zhang e rp: 1203014041 apda3020seck/j3-pf recommended soldering pattern (units : mm; tolerance: 0.1) reel dimension tape dimensions (units : mm)
spec no: dsan2822 rev no: v.3a date: feb/13/2017 page: 5 of 5 approved: wynec checked: allen liu drawn: l.t.zhang e rp: 1203014041 packing & label specifications apda3020seck/j3-pf terms and conditions for the usage of this document 1. the information included in this docum ent reflects representative usage scenarios and is intended for technical reference on ly. 2. the part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. before production usage customer should refer to the latest datasheet for the updated specifications. 3. when using the products referenced in this document, please make sure the produc t is being operated within the environmental and electrical limits specified in the dat asheet. if customer usage exceeds the spec ified limits, kingbright will not be respon sible for any subsequent issues. 4. the information in this document applies to typical usage in consumer electronics applicati ons. if customer's application ha s special reliability requirements or have life-threatening liabilitie s, such as automotive or m edical usage, please consult with kingbright representative for further assistance. 5. the contents and information of this document may not be reproduced or re-transmitted without permission by kingbright. 6. all design applications should refer to kingbright application notes available at http://www.kingbrightusa.com/applicationnotes
|
